Glitter Heat Transfer Vinyl Made Easy

Glitter Heat Transfer Vinyl Made Easy

Head on over to Craft-e-Corner Cricut Community Facebook Group for more inspiration and education!

Did you know that glitter iron-on heat transfer vinyl is magic?  When you cut it, the cut lines magically disappear! I’ve learned a few tricks to help reveal the lines to make weeding easier, and you might be surprised. Read on below for some ways to make glitter HTV easier to handle.

glitter htv hacks

If you’ve ever worked with smooth iron-on heat transfer vinyl, you have probably relied on the lines that your blade leaves behind as a guide on where to weed. When you work with glitter heat transfer vinyl, those lines are quite hard to see. It’s like magic - they just disappear!  Here are some suggestions I’ve tried to try to make them reappear (thus making glitter heat transfer easier to manage).

I created this adorable owl hat using glitter heat transfer. (You can read more about this hat project on my post, How to Heat Press HTV to a Hat.)

Tips and tricks on how to weed glitter heat transfer vinyl. Adding vinyl to a hat!

When I cut the design, I got ready to weed and noticed there were no lines in sight! The machine had cut the material, but there were no cut lines to help me weed the interior parts of the design.

I did some research and pulled together these recommendations for how to uncover the weed lines once again. Here are my conclusions.

Tip 1: Use a Light Table

Glitter HTV weeding trick#1- use a light table.

Methodology: If you put a glitter heat transfer design on a light box or light table, you may be able to see the light shine though where the design was cut.

My results: I don’t have a light table, so I tried holding the design up to a brightly lit window. It actually helped a little, but wasn’t project friendly. If you’re doing a lot of glitter heat transfer, it’s totally worth the investment to get a light table. Helpful, but not helpful today.

Verdict:  Plausible.

Tip 2: Freeze the Iron-On

Glitter HTV vinyl weeding trick #2- freeze the vinyl!

Methodology: Throw your cut design in the freezer for a bit. Vinyl shrinks when it freezes which should pull the design pieces away from each other, creating a larger gap that is easier to see with glitter heat transfer.

My results: I tried it out, it didn’t work that well. The design warmed up to room temperature (which did not take long), and then I was right back a square one.

Verdict: Fail.

Tip 3: Draw with Cricut Pen

Glitter heat transfer vinyl weeding trick #3- use a sketch pen

Methodology: Before unloading your design from your machine, swap the blade for a sketch pen and have the machine draw the design with a sketch pen. This will leave you with a visible outline that you can then use to weed.

My results: I did not attempt this. I was putting my design on a light-colored hat and did not have another hat, nor more heat transfer vinyl to do it all over again should the pen bleed through the vinyl or show on the inside of the hat. I’d give this a go with dark iron-on and dark fabric, but probably not otherwise.

Verdict: Plausible.

Tip 4: Apply Baby Powder

Glitter heat transfer weeding trick #4- use baby powder!

Methodology: Cut the design and dust with baby powder.

My results: This sounded harmless and easy enough, so I gave it a whirl.

Add a dash of baby powder to glitter heat transfer and watch the cut lines magically reappear- it's magic!

Verdict: Perfection!

Just a touch of baby powder will help your weed lines appear on glitter heat transfer vinyl.

Give a (very) light dusting of baby powder, rub it around on the design and it magically highlights all the cut lines making it easy to see where you need to weed. The baby powder did not seem to have any effect on the vinyl. The vinyl stayed stuck to the carrier sheet without any problem and transferred to the hat easily as well.

Have you used one of these techniques with success?  What works for you?  If not, give one a try and let me know how it goes!

Happy Crafting! - Kala

FEATURED SALES

Back to blog

3 comments

when im weeding the glitter vinyl it doesnt cut along were its supposed to weed off the opposite way

olivia luna

another ??? im having problems weeding the shinny sliver vinyl

olivia luna

how do i clean the black gunk off the inside of the cricket right under the 2 long silver bars

olivia luna

Leave a comment

Please note, comments need to be approved before they are published.